Where should toilet supply line be placed?

Insert the line through the bottom plate on the wall, approximately 8 inches to the left of the toilet’s center line. Connect this supply line at the water line attached to the sink. Use a 90-degree elbow or stub-out fitting to insert the water line into the surface plane of the wall.

How high off the floor should a toilet supply line be?

Supply line (height): Ideally, the toilet’s water supply line enters the room at 8 1/4 inches above the floor. More broadly, this cold-water-only pipe creates one hole between 5 and 10 inches above the floor.

How far off the floor should a toilet valve be?

With the toilet removed, you can see the toilet flange and measure its height above the floor. The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.

How do you rough in a toilet water line?

How To Rough-In a Toilet (with Dimensions) – YouTube

How far should toilet supply stick out from wall?

The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall.

How far should toilet drain be from wall?

The rough-in distance in the newer homes from the wall to the center of the toilet drain is 12-inch, while, older homes have a distance of anything between 10- or 14 inches. A wall-mounted toilet also needs a 10 inch thick wall to accommodate the flushing system.

How long should a toilet water supply line be?

Typically they are 3/8” in diameter, but toilet supply line size can vary in length, usually anywhere from 9” to 20”.

How do you run a toilet supply line?

How to Install a Toilet Supply Line – Aubuchon Hardware – YouTube

Can you replace a 10 inch rough in toilet with a 12-inch rough in toilet?

The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.

Can a shower and toilet share the same drain?

In the US, with modern regulations, in most municipalities, yes, they do. The water and solids from your toilet waste line and the water from your drains end up in the same sewer line, if you have access to a municipal sewer system.

Does toilet need to be on outside wall?

Chances are if you are asking yourself this question you may have been told by your builder or designer that the toilet needs to be placed against the outside wall. While there are good reasons to do so, it is not always necessary. In fact, many bathroom layouts have the toilet set against an internal wall.

Are all toilets the same distance from the wall?

Toilet Rough In Dimensions: A toilet’s rough-in measurement is the space between the wall behind the toilet and the center of the waste pipe. Standard toilet rough in dimensions are 12 inches but can be anywhere from 10 to 14 inches in some cases.

How far away should the toilet be from the vanity?

Toilet placement

A toilet should have some elbow room between it and another fixture or vanity. The NKBA’s recommendation is at least 18″. Codes allow a minimum distance of 15″.

How far should a toilet flange be from the side wall?

In general, the toilet rough-in distance is 12″ from the center of the toilet flange to the back wall for a typical toilet. There should also be a minimum of 15″ from the centerline of the toilet to any wall or object on either side of the toilet.

How far can you move a toilet from the stack?

If your waste line has a diameter of 3 inches, you can place the toilet within six feet of your stack. The toilet can also be as far as 10 feet from your stack, if the diameter of the waste line is 4 inches.

Are toilet and faucet supply lines the same?

A faucet, toilet, and refrigerator’s ice maker use a similar water supply line. A refrigerator’s ice maker uses 1/4-inch tubing with 1/4-inch compression fittings on both ends.

How often should I change my toilet supply line?

How Often Should You Replaces These Braided Supply Lines? The general rule of thumb is to replace all your supply line hoses every 5 years as a preventative measure to protect your home against any potential leaks.

Which toilet supply line is best?

Our Recommended The Best Toilet Supply line in 2022

  1. Fluidmaster B1T12CS CLICK SEAL Toilet Supply Lines. …
  2. SharkBite 24656 Toilet Connector. …
  3. SharkBite 24686 Click Seal Water Supply Hose. …
  4. Eastman 48088 Flexible Toilet Connector. …
  5. PROCURU Faucet Hose Connector. …
  6. Fluidmaster B1T16 Water Supply Line.

How do you set up a supply line?

Install Fluidmaster’s Click Seal Faucet Supply Line – YouTube

How many supply lines does a toilet have?

Every toilet and sink in your home has water supply lines that connect into the home’s fresh water system. Every toilet has one supply line and every sink has two – one for hot and one for cold.

Why would I want an elongated toilet bowl?

Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.

What is comfort height toilet?

Traditional toilets are 15 inches high. Comfort height toilets (or “right height” toilets) have higher seats than traditional toilets, usually between 17 inches and 19 inches. Comfort height toilets are becoming a popular option for many households.

How do you move a toilet closer to the wall?

Install the Offset Flange

  1. Positions the offset flange so that the bent end moves the flange opening closer to the wall. …
  2. Make sure the back of the offset flange connects snugly with the drainage pipe. …
  3. Check to make sure that the flange’s opening is sitting flush and even against the bathroom floor.

Where is toilet vent pipe?

It will be found in a basement or crawlspace coming straight down from your house. In most cases it will be made of either cast iron or, in modern homes, PVC pipe, usually colored black. Most of these pipes will be at least 3 inches in diameter. Have someone flush the toilet and listen for a large draining sound.

Can you poop in the shower?

Showers don’t have enough pressure or volume of water for bowel movements to pass through drainage systems. The diameter of a sewer pipe is much wider than that of the drain. When a toilet flushes, the large volume of water can move faeces, which showers are unable to do so.

How many toilets can you put on a 3 inch line?

How Many Bathrooms With Toilets Can You Have In Your House

Can you put a toilet anywhere?

On a serious note, it is absolutely possible to install a toilet, even a bathroom as a matter of fact, anywhere in your house. In the past, many homeowners have had the idea of their dream bathroom crushed because the location was simply too far away from the main drain.

How far can a toilet be from the soil pipe?

The furthest the toilet would be away from the pipe is 2metres due to the size of the bathroom. I’d also have to keep all pipe work above the concrete floor and accessible in some way in case future plumbing work is needed.

Can you put toilet outside?

Plumbing can be placed on an exterior wall. The supply pipes have to be insulated to keep them from freezing.

What is the footprint of a toilet?

A toilet “footprint” is basically the measurement or size of where the bottom of the toilet pedestal meets the floor.

Can you replace a 14 inch rough-in toilet with a 12 inch rough-in toilet?

You can, but the back of the toilet tank will be two inches further away from the wall. The “rough-in” dimension refers to the distance from the wall framing (½-⅝″ behind the finished wall surface) to the center of the sewer pipe on the floor. Standard rough-in is 12 inches.

How do I know if my toilet is a 10 or 12 rough?

If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.

How close can toilet be to bathtub?

It is recommended that the distance from the centerline of a toilet and/or bidet to any bath fixture, wall, or other obstacle should be at least 18 inches. The minimum distance from the centerline of a toilet and/or bidet to any bath fixture, wall, or other obstacle is 15 inches.

Why is the toilet next to the tub?

Toilets tend to be next to bathtubs because both of them tend to be in a small room that is kept rather private from the rest of the house and because both of them need to have fairly substantial plumbing in order to operate correctly.

Is it expensive to relocate a toilet?

The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move. Connecting the toilet to the existing sewer line can be a bit tricky for your plumber.

Can toilet waste pipe run under floor?

3 Answers from MyBuilder Bathroom Fitters

Soil pipes are generally located on an outside wall and enter the bathroom as close as possible to the toilet location. They can be mounted on the floor, but usually pipes run below the floor in-between the floor joists.

Can I move a toilet a few inches?

For the waste water line, an offset toilet flange will allow you to move the toilet a couple of inches in any direction without having to cut a new hole in the floor or reconstruct the waste water pipe.